Two Genuine Weber Stainless Steel Tube Burners and one Crossover Flame Tube set for Weber Genesis Silver A, Spirit 500 and Spirit E-210 model years 2007 to 2012. Two 27in. Front and Rear Tube Burners, and one 10-1/2in. Gas/Flame Crossover Burner Tube. Weber stainless steel burners feature venturi's with built-in wire-mesh screen spider guards. Replacement hardware included. Genuine Weber Part, replaces Weber Part 7507.

Are you experiencing uneven heat in your Weber BBQ grill? Replace your burners with our Weber® Stainless Steel Tube Burner Set. Over time, your grill's original burners gas ports become blocked, cracked, or rusted, leading to uneven heat and reduced efficiency. Turn up the heat with a clean consistent flame by replacing old burners with a long lasting set of high quality stainless steel Weber® burners from Grillparts.com. Get even surface heat to your cooking grates, just like when your grill was new!

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series

Set Includes:

• (2) 27in. Front and Rear Stainless Steel Tube Weber Burners
• (1) 10-1/2in. Gas/Flame Crossover Burner Tube
• Mounting hardware

One Genuine Weber Stainless Steel 10-1/2in. Crossover Flame Tube Burner for Weber Genesis Silver A, Weber Spirit 500 and Weber Spirit E-210 grills, model years from 2007 to 2012 that feature two main burners. This is the smaller burner tube designed to transfer flame from the front ignited burner to the rear burner tube.

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series

What’s Included:

• (1) Genuine Weber Crossover Gas/Flame Burner Tube:
• Fits Weber Genesis Silver A, Spirit 500, Spirit 200 Series
• Model Years 2007-2012

Genuine Weber® Flavorizer Bars made in Stainless Steel. Set of five Flavorizer Bars/Burner Shields that measure 21-1/2in.

Weber® Stainless Steel Flavorizer Bars are shields that act like the armor your burners deserve, protecting them from the relentless assault of grease, drippings, and whatever else the grill gods throw their way. Not only does this extend the life of your burners, but vaporize drippings like it’s nobody's business. Infuse your food with that smoky, savory goodness while protecting your burners with new Weber Flavorizer Bars from Grillparts.com.

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (5) 21-1/2in. stainless steel Weber Flavorizer Bars:
• Durable Stainless Steel
• Genuine Weber® Replacement Part

Genuine Weber® Flavorizer Bars made in Porcelain Coated Steel. Set of five Flavorizer Bars/Burner Shields that measure 21-1/2in.

Weber® Porcelain Coated Steel Flavorizer Bars are shields that act like the armor your burners deserve, protecting them from the relentless assault of grease, drippings, and whatever else the grill gods throw their way. Not only does this extend the life of your burners, but vaporize drippings like it’s nobody's business. Infuse your food with that smoky, savory goodness while protecting your burners with new Weber Flavorizer Bars from Grillparts.com.

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (5) 21-1/2in. Porcelain Coated Steel Weber Flavorizer Bars:
• Genuine Weber® Replacement Part

Two piece porcelain coated stamped steel cooking grate set for Weber Genesis Silver A, Spirit 200 Series and Spirit 500 Series model years 2012 and prior, with control knobs located on the right hand side table. Set includes two sections measuring 11-3/8in. x 15in. each; for a total overage area of 22-3/4in. x 15in.

Freshen up your grilling experience! Replace your cooking grates where the meat greets the heat with these sleek, porcelain enameled stamped steel replacement cooking grates for older Weber® grills. Rust-resistant and easy to clean, these porcelain enameled cooking grates for Weber® Grills from Grillparts.com spread heat and are great for everyday grilling. 

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (2) Stamped Steel Porcelain Coated Cooking Grates for Weber Grills:
• Measure 11-3/8in. x 15in. each:
• Total overage area: 22-3/4in. x 15in.
• IMPORTANT: PLEASE VERIFY DIMENSIONS.
• Quality Aftermarket Part.

Genuine Weber® Genesis Silver A model and Spirit 200 Series (2007-2008) chrome plated hanging warm up basket. Basket hangs from the grill lid and swings as the lid is opened.

The Weber® Chrome Plated Warm Up Basket, your grilling sidekick, literally elevating your barbecue game to new heights. It's not just a hanging rack; it's a cozy retreat for your finished masterpieces, keeping them warm and toasty while you finish up the main event on the grill! 

Please measure your warm up basket including hanging pins. Full length tip-to-tip measurement of the hanging pins is 23-3/4in.

Fits the following Weber Grills:

• Weber® Genesis Silver A
• Spirit 200 Series (2007-2008)
• Genuine Weber Part.

Genuine Weber® Two piece porcelain coated stamped steel cooking grate set for Weber Genesis Silver A, Spirit 200 Series and Spirit 500 Series model years 2012 and prior, with control knobs located on the right hand side table. Set includes two sections measuring 11-3/8in. x 15in. each; for a total overage area of 22-3/4in. x 15in.

Freshen up your grilling experience with genuine Weber Cooking Grates! Replace your cooking grates where the meat greets the heat with these sleek, porcelain enameled stamped steel replacement cooking grates for older Weber® grills. Rust-resistant and easy to clean, these porcelain enameled cooking grates for Weber® Grills from Grillparts.com spread heat and are great for everyday grilling. 

Fits these following Weber® gas grill models:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (2) Weber® OEM Stamped Steel Porcelain Coated Cooking Grates for Weber Grills:
• Measure 11-3/8in. x 15in. each:
• Total overage area: 22-3/4in. x 15in.
• IMPORTANT: PLEASE VERIFY DIMENSIONS.
• Genuine Weber OEM Part.

Genuine Weber® Channel formed, rolled stainless steel cooking grate two piece set. Crafted with precision and durability in mind, these grates are manufactured to seamlessly fit into Weber Spirit 200 series, Spirit 500 and Genesis Silver A models, ensuring a perfect fit for your grill.

Freshen up your grilling experience! Replace your cooking grates where the meat greets the heat with these sleek, stainless steel channel formed cooking grates for older Weber® grills. Rust-resistant and easy to clean, these stainless steel channeled Weber® cooking grates from Grillparts.com spread heat for nice sear marks and are great for everyday grilling. 

Fits the following Weber Grills:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (2) Weber® Channel formed stainless steel cooking grates:
• Measure 11-3/8in. x 15in. each:
• Total overage area: 22-3/4in. x 15in.
• IMPORTANT: PLEASE VERIFY DIMENSIONS.
• Genuine Weber Part.

Genuine Weber® Two piece cast iron cooking grate set for heat retention with porcelain enamel matte finish for easy clean up. Freshen up your grilling experience with new Genuine Weber® cast iron cooking grates! Replace your cooking grates where the meat greets the heat with these sleek, matte finish grates. The porcelain enamel finish is rust-resistant and easy to clean. these cast iron Weber® cooking grates from Grillparts.com spread heat for nice sear marks and are great for everyday grilling. 

Fits the following Weber Grills:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)
• Genuine Weber Part.
• This set replaces Weber part# 7522.

What’s Included:

• (2) 11-3/8in. x 15in. Weber cast iron cooking grates.
• Total Coverage: 22-3/4in. x 15in.
• Please Verify Dimensions.

Genuine Weber® Heavy Duty Chrome Plated Warming Rack for Spirit 200 (2007-08), Spirit 500 and Weber Genesis Silver A that fits across the top rear of a variety of Weber gas grills. Heavy gauge steel Weber Warming Rack at 24in. x 4-3/4in. measured from tip-to-tip of the rod ends (attachment points that fit in cradle notches in the top rear of your grill.)

Compatible with the following Weber Grills:

• (Please measure your rack, including hanging pins)
• Spirit 200 (2007-08)
• Spirit 500
• Genesis Silver A (2000-05)

The Weber® Chrome Plated Warming Rack, your grilling sidekick, literally elevating your barbecue game to new heights. It's not just a rack; it's a cozy retreat for your finished masterpieces, keeping them warm and toasty while you finish up the main event on the grill! 

What’s Included:

• (1) Weber® Warming Rack for Weber Spirit 200, 500 and Genesis Silver A:
• Chromed Steel Construction
• 24in. x 4-3/4in. (Please measure your warming rack width including rod tips)
• Genuine Weber OEM Part. 

High Quality Channel formed, rolled stainless steel cooking grate two piece set. Crafted with precision and durability in mind, these grates are manufactured to seamlessly fit into Weber Spirit 200 series, Spirit 500 and Genesis Silver A models, ensuring a perfect fit for your grill. High Quality alternative to Weber OEM Part 65905.

Freshen up your grilling experience! Replace your cooking grates where the meat greets the heat with these sleek, stainless steel channel formed cooking grates for older Weber® grills. Rust-resistant and easy to clean, these stainless steel channeled cooking grates for Weber® grills from Grillparts.com spread heat for nice sear marks and are great for everyday grilling. 

Fits the following Weber Grills:

• Weber Genesis Silver A
• Weber Spirit 500 series
• Weber Spirit 200 series
• (Model Years Prior To 2013)

What’s Included:

• (2) Channel formed stainless steel cooking grates for Weber® :
• Measure 11-3/8in. x 15in. each:
• Total overage area: 22-3/4in. x 15in.
• IMPORTANT: PLEASE VERIFY DIMENSIONS.
• High Quality Weber OEM alternative.

Genuine Weber® Locking 2in. Grill Caster Wheel with Leg Insert. Smoothly wheel your Weber gas grill into position with the aid of a gas grill replacement caster wheel for your Weber Grills' Ranch Kettle, select Performer, Genesis and other varying models.

Don't get caught flat-footed! Replace your Weber Locking Grill Caster Wheel when grill portability is necessary. Replace any defunct casters with one of these genuine Weber caster wheels. Once in place, prevent wayward movement with the built-in locking mechanism for supreme steadiness.

• High-grade plastic easily supports the weight of your grill
• Wheel turns unimpeded on axle inside curved housing
• Easily pops into place

What’s Included:

• (1) 2in. Locking Caster Wheel with Leg Insert for Weber® grills.
• One included, multiples may be necessary.

Fits the following Weber Grills:

• Platinum I
• Genesis 1000-5500
• Genesis A/B/C (2002-2003 model years)
• Genesis Silver A (2002-2003)
• Genesis® Silver B and C (prior to 2004)
• Genesis Gold B/C (model year 2002-2003)
• Ranch Kettle
• Performer (prior to 2005 model year)
• Performer Touch-N-Go

Set of two 6in. diameter Genuine Weber replacement black plastic wheels with three Axle Retaining Caps fits a variety of Weber Grills. Axle hole diameter measures 3/8in. Each wheel features Weber brand name impressions on the side walls. Includes (3) Axle retaining caps and wheel replacement instructions. Genuine Weber Part.

Don't get caught flat-footed! Replace your Weber Grills Wheels for the right cooking height and when your grill needs to be on-the-move with these genuine replacements from Grillparts.com.

What’s Included:

• (2) Genuine Weber 6in. diameter black plastic wheels.
• (3) Axle Retaining Caps
• Axle hole diameter measures 3/8in.
• Fits models: 1343, 1321001, 21001, 21004, 61001, 61004, and 61504.

Genuine Weber® 6in. diameter replacement plastic wheel for most Weber Charcoal Kettle Grills. Don't get caught flat-footed! Replace your Weber Kettle Wheels for the right height and when grill portability is necessary.

Fits most Weber Performer kettle grills and other grills that require a 6 inch diameter replacement grill wheel.

What's Included:

• (1) 6in. Weber Kettle Wheel
• (2) Axle hub caps
• Axle hole opening is 3/8in. diameter.
• Compatible with 18 and 22in. Kettle Grills
• Genuine Weber Part
• Sold Individually. 

Heavy duty Genuine Weber® Locking 2-7/8in. Grill Caster Wheel with Leg Insert. Smoothly wheel your Weber gas grill into position with the aid of a gas grill replacement caster wheel for your Weber Grills' Genesis 300, Summit Series and Spirit model.

Don't get caught flat-footed! Replace your Weber Locking Grill Caster Wheel when grill portability is necessary. Replace any defunct casters with one of these genuine Weber caster wheels. Once in place, prevent wayward movement with the built-in locking mechanism for supreme steadiness.

IMPORTANT: Please verify dimensions.

• Dia. of the wheel measures 2-7/8in.
• Stem length measures 1-3/8in.

Fits the following Weber Grills:

• Spirit series (2009-2012)
• Genesis series (2007-2011)
• Summit series (2007-2011)
• Replaces older Weber Part# 79500

What’s Included:

• (1) 2-7/8in. Locking Caster Wheel with Leg Insert for Weber® grills.
• One included, multiples may be necessary.
• Genuine Weber OEM part

1-7/8in. Diameter Genuine Weber Light Gray Plastic Gas/Heat Control Knob fits a variety of Weber Genesis and Spirit models, along with Summit 400/600 Series-model years Prior to 2000. Twist your way to BBQ magic with new Weber heat control knobs for your Weber gas grill from Grillparts.com. Replace your broken, worn or lost Weber® Heat/Gas Control Knobs with these exact genuine replacements.

Fits the following Weber Gas Grill Models:

• Summit 400/600 Series-model years Prior to 2000
• Spirit 500 & 700
• Genesis 1000 & 2000 for older series grills
• Genesis 1000-5500 Prior to 2004
• Genesis Silver & Gold Prior to 2004 Model Year

What’s Included:

• (1) Genuine Weber Light Gray Plastic Gas/Heat Control Knob:
• Measures 1-7/8in. diameter.
• Stem on bottom is 1-3/8in. in length.
• Sold individually.
• Please Verify Dimensions.
• Genuine Weber Part.

Genuine Weber® 8in. diameter replacement plastic wheel for most Weber 26in. Kettles (2009-14), Ranch (2000-19), and Q 300/320 (2006-13) Kettle Grills. 8in. diameter black plastic wheel with gray colored snap-in hub-cap with Weber name detail. Features a 3/8in. diameter axle hole. Axle shaft hub extends 1/4in. beyond the back of the wheel frame. Axle hub caps and hardware not included.

Don't get caught flat-footed! Replace your Weber Kettle Wheels for the right height and when grill portability is necessary. 

What's Included:

• (1) 8in. Weber Kettle Wheel
• (1) Gray Decorative Hub Cap
• (2) Axle Caps/Wheel Retainers for installation.
• Axle hole opening is 3/8in. diameter, Axle shaft hub extends 1/4in. beyond wheel frame.
• Genuine Weber Part
• Sold Individually.

Genuine Weber Curved gray molded composite lid handle, 22-1/2in. length to replace the grill hood handle on Spirit 210 (2007-2008), and Weber Spirit 500 and Genesis Silver A models (2005-2006).

What’s Included:

• (1) Genuine Weber Curved gray molded composite lid handle:
• Please verify measurements!
• Measures 22-1/2in, measured in a straight line from tip to tip, including the attachment endpoints.
• Genuine Weber Part.

Set of two 2-1/8in. diameter Genuine Weber® Spirit gas/heat control knobs that fit Weber Spirit 310/320 grills built between 2009 and 2012, but also fit older Spirit models. Weber Spirit black control knobs feature inset translucent position indicators. 

Twist your way to BBQ magic with new Weber Spirit heat control knobs from Grillparts.com. Replace your broken, worn or lost Weber® Heat/Gas Control Knobs with these exact genuine replacements.

Dimensions:

• 2-1/8in. diameter
• 1-1/2in. stem. (These are from 2009 models and also will fit older Spirit models)

What’s Included:

• (2) Gas/Heat Control Knobs for Weber Spirit gas grills.
• Genuine Weber® replacement parts

Pack of three Genuine Weber® axle hub caps/wheel retainers. These Caps fit most Weber gas and charcoal kettle grills with 6in. or 8in. wheels.

Wheels coming off your backyard companion? Get the wheels back on with a set of these genuine Weber Hub Caps from Grillparts.com.

What’s Included:

• (3) Weber Wheel Hub Caps/Retainers for 6in. and 8in. Wheels

Genuine Weber® Locking 2-5/16in. Grill Caster Wheel with Leg Insert. Smoothly wheel your Weber gas grill into position with the aid of a gas grill replacement caster wheel for your Weber Grills' Summit Gold/Silver/Platinum, Spirit or Genesis model (more below).

Don't get caught flat-footed! Replace your Weber Locking Grill Caster Wheel to get it level and when grill portability is necessary. Replace any defunct casters with one of these genuine Weber caster wheels. Once in place, prevent wayward movement with the built-in locking mechanism for supreme steadiness.

• High-grade plastic easily supports the weight of your grill
• Wheel turns unimpeded on axle inside curved housing
• Easily pops into place

 
What’s Included:

• (1) 2-5/16in. Locking Caster Wheel with Leg Insert for Weber® grills.
• One included, multiples may be necessary.

Fits the following Weber Grills:

• IMPORTANT: Please verify dimensions.
• Summit Gold/Silver/Platinum models
• Spirit and Genesis (model years 2004-2008)
• Performer Kettle models prior to 2005
• Ranch Kettles. 
• Genuine Weber Part.

Set of three Genuine Weber® Spirit gas/heat control knobs. Weber Spirit gray 2-1/4in. diameter gas/heat control knobs fit Weber older (2007+/-) Spirit models. 

Twist your way to BBQ magic with new Weber heat control knobs for your Spirit grill from Grillparts.com. Replace your broken, worn or lost Weber® Heat/Gas Control Knobs with these exact genuine replacements.

What’s Included:

• (3) Light gray Gas/Heat Control Knobs for Older Weber Spirit grills.
• Measures 2-1/4in. diameter
• Stem measures 1-3/8in.

Fits the following Weber Models:

• Spirit E-210 (2007)
• Spirit SP-310, E-310
• Spirit E-320 (2008)

14ft. length propane adapter hose with stainless steel overbraid.  Long reach is ideal for extending your gas line for Camping and RVs. Allows for a full-size propane tank to be used with your portable grill or appliance. The extra long 14ft. length offers great versatility and safety for locating your camping firepit, etc.

Features an easy-screw-on large green knob that connects to the full-size propane tank. The small brass fitting end attaches to your propane appliance (in the same manner as a small propane camping bottle would). Hose is wrapped in stainless steel overbraid for added protection and durability as well as a strong deterrent for rodents.

What’s Included:

• (1) 14ft. Propane Adapter Hose with Stainless Steel Overbraid, with attached QCC1 Propane Gas fitting from full size tank to hose, and from hose to US standard threaded 1 pound disposable tank type appliance fitting.

3/8in. Quick Connect fitting with integrated On/Off ball valve. Features “Couple Safe Technology Thermal Shut-off Device Protection”. Designed to only allow gas line connection when the valve is in the closed position. Dust plug included.

Female threaded (3/8in. FNPT) end fits onto 3/8in. fixed supply line.

What’s Included:

• 1 On/Off Ball Valve Quick Connect Fitting
• Includes Female threaded (3/8" FNPT) end fits onto 3/8" fixed supply line, Quick Connect coupler at other end.

3/8in. Quick Connect Fitting for use with 3/8in. gas hose. 3/8in. FNPT (Female National Pipe Thread) end, and Quick Connect Coupler on the other. Commonly used for Quick Connecting BBQ Grills (and other low pressure BTU output outdoor gas appliances) to a permanent gas supply line. ANSI certified for natural (NG) and propane (LP) gas use. Dust plug included.

Quick connect components make it easy to connect and disconnect the grill from a fixed gas supply line quickly and without tools. This convenience is especially beneficial if you need to move the grill or store it away when not in use.

What’s Included:

• 3/8" Gas Line Quick Connect Fitting

High performance 2-Stage gas grill regulator and 30in. of high-pressure heavy duty hose with 3/8in. fitting assembly. This low-pressure BBQ Grill Regulator is used for connecting commercial grade BBQ & Catering Grills requiring gas input in excess of 100,000 BTUs per hour through a green Type 1 fitting to propane tank. These 2-stage regulators also work well with larger tank-fed outdoor firepits that often trigger bypass mode on portable tanks.

Features two regulators that allow the Type 1 tank connection to disperse a higher volume of gas to pass through the tank connection before going into bypass mode (which kills the available gas pressure). Used for LP (Propane) gas only.

What’s Included:

• 2-Stage Regulator and 30in. Hose Assembly which includes:
• 3/8in. ID high pressure hose, 30in. length.
• 3/8in. flare fitting hex nut for the appliance end connection, and a POL green hand nut for the propane tank connection.
• One 3/8in. to 3/4in. brass adapter included.  

Set this automatic Gas Timer to your desired grilling/gas flow time from one to three hours, and it will safely shut off gas to your grill automatically. Preset intervals from one, up to three hours. Works with either natural gas (NG) or propane (LP).

Has your grill ever been accidentally left “On”? Set this automatic Gas Timer to your desired grilling time, and be worry free. Never fret about leaving your grill on for wasteful hours until your tank runs dry, or even days if you're connected to natural gas!

Product Details:

• This timer accommodates 1/2in. NPT piping (both ends).
• 100,000 BTU rating.
• Natural Gas or Propane.
• Quality FireMagic Part.

What’s Included:

• Automatic Gas Timer: 1hr, 2hr, or 3hr duration. 
• Installation/operating instructions.

Replacement Timer Control Knob for 1hr. to 3hr. Automatic Gas Timer (Item# 3090). Black plastic control knob features a sure grip edge surface and white lettered graphics indicating "Off" and 1-2-3 hour incremental settings. Quality FireMagic Part.

What’s Included:

• 1 Control Knob for Automatic Gas Timer Valve in 1hr, 2hr, 3hr increments.

Set this automatic Gas Timer to your desired grilling/gas flow time in available 20min. increments, and it will safely shut off gas to your grill automatically. Preset intervals from 20 minutes to 1 hour. Works with either natural gas (NG) or propane (LP).

Has your grill ever been accidentally left “On”? Set this automatic Gas Timer to your desired grilling time, and be worry free. Never fret about leaving your grill on for wasteful hours until your tank runs dry, or even days if you're connected to natural gas!

Details:

• Accommodates 1/2in. NPT piping (both ends).
• 100,000 BTU rating.
• Natural Gas or Propane.
• Quality FireMagic Part.

What’s Included:

• Automatic Gas Timer Assembly, 20/40/60min. durations. 
• Installation/operating instructions.

Replacement Timer Control Knob for 20/40/60 minute Automatic Gas Timer (Item# 3092). Black plastic control knob features a sure grip edge surface and white lettered graphics indicating "Off" and 20, 40 and 60 minute incremental settings. Quality FireMagic Part.

What’s Included:

• 1 Control Knob for Automatic Gas Timer Valve in 20/40/60 minute increments.

Weber Grill Replacement Brass Gas/Heat Control Main Burner Valve with external mounting threads that fits a variety of Weber grill models manufactured in 2006 and prior years.

Are your main burner Weber Gas Control Valves sticky, leaky or malfunctioning? Replace yours and light up those burners and properly regulate the flow of fuel safely. Keep the flames dancing just right; order a new replacement gas control valve for your Weber from Grillparts.com today!.

Fits a variety of Weber models:
2006 and older Weber Grills with control knobs located on the right hand side table, which includes various Genesis I-V, 1000-5000, Gold B/C, Silver A and Spirit 500/700 models.

Measurements:

• 3-9/16in. from tip of control knob stem to bottom of valve body.
• 2-1/4in. from tip of burner orifice stem to the tip of the mounting threads
• Features external/outside mounting threads that screw into a hole on the manifold rail/pipe.

What’s Included:

• (1) Brass Main Burner Gas Control Valve for Weber Grills
• (1) Orifice, Size #61. (Note: Orifice sizes vary depending on BTU ratings. In order to maintain the performance of your BBQ, reuse your original orifice/size when possible.
• Sold individually.
• Quality Aftermarket Part

Outdoor gas appliance/bbq grill 1 to 3 hour Automatic Gas Timer with included stainless steel mounting panel/box assembly.

Has your grill ever been accidentally left “On”? Set this automatic Gas Timer to your desired grilling time, and be worry free. Never fret about leaving your grill on for wasteful hours until your tank runs dry, or even days if you’re connected to natural gas! A must have for your home, rental homes, AirB&B, or commercial applications.

Automatic Timer: Set this automatic Gas Timer to your desired grilling/gas flow time from one to three hours, and it will safely shut off gas to your grill automatically. Preset intervals from one, up to three hours. Works with either natural gas (NG) or propane (LP).

• 1-2-3 hour interval gas valve timer.
• 100,000 BTU rating.
• Natural Gas or Propane.

Mounting Panel Box:

• Premium Stainless Steel enclosure/recessed mounting box with Push to Open/Close magnetic door.
• Outer Dimension with Mounting Overhang: 7-3/4in. x 7-3/4in.
• Rough-in Size for Recess: 6-1/2in. x 6-1/2in. square opening.
• Preassembled Gas Timer and Mounting Box with internal plumbing, ready to mount.
• Two internally mounted 1/2in. flare connector adapters with “out/in” labels.

What’s Included:

• Automatic Gas Timer and Mounting Box Assembly: 1hr, 2hr, or 3hr durations. 
• Installation and operating instructions.
• Quality FireMagic Part.

22in. length Propane/LP gas hose and regulator assembly. Brass male pipe threaded end (3/16" ID and 3/8" OD) attaches to the grill manifold. Propane regulator features a QCC1 connection with large hand nut that attaches to the propane tank. Overall length of complete assembly is 25 inches.

Is your gas line cracked, split, or damaged? Is your regulator faulty and not supplying enough fuel to your burners? Replace and/or faulty regulator with QCC1 Hose and Regulator Kit. Check your gas line for cracks, rodent tooth marks and potential leaks around fittings. The diaphragm inside the regulator can become damaged or weakened. Over time, regulators experience wear from exposure to heat, weather, and general use. Order your replacement hose and regulator assembly from Grillparts.com today!

What’s Included:

• (1) 22in. hose with attached regulator assembly with integrated QCC1 to-tank connection.
• Male pipe threaded end. (Attaches to female fitting on grill manifold)

5/16in. ID propane/LP gas hose in 24 inch length with a brass 3/8in. female hex nut flare connector, assembled to propane regulator that features a QCC1 connection with large hand nut that attaches to the propane tank. Replaces #7502 Genuine Weber Part. 

Is your gas line cracked, split, or damaged? Is your regulator faulty and not supplying enough fuel to your burners? Replace and/or faulty regulator with this Genuine Weber part. Check your gas line for cracks, rodent tooth marks and potential leaks around fittings. The diaphragm inside the regulator can become damaged or weakened. Over time, regulators experience wear from exposure to heat, weather, and general use. Order your replacement hose and regulator assembly today!

What’s Included:

• 1 5/16in. x 24in. hose with attached regulator assembly with integrated QCC1 to-tank connection.
• Instruction sheet.
• Genuine Weber Part. 

5/16in. ID propane/LP gas hose in 40 inch length with a brass 3/8in. female hex nut flare connector, assembled to propane regulator that features a QCC1 connection with large hand nut that attaches to the propane tank. Genuine Weber Part. 

Is your gas line cracked, split, or damaged? Is your regulator faulty and not supplying enough fuel to your burners? Replace and/or faulty regulator with this Genuine Weber part. Check your gas line for cracks, rodent tooth marks and potential leaks around fittings. The diaphragm inside the regulator can become damaged or weakened. Over time, regulators experience wear from exposure to heat, weather, and general use. Order your replacement hose and regulator assembly today!

What’s Included:

• (1) 5/16in. x 40in. hose with attached regulator assembly with integrated QCC1 to-tank connection.
• Instruction sheet.
• Genuine Weber Part. 

5/16in. ID propane/LP gas hose in 24 inch length with a brass 3/8in. female hex nut flare connector, assembled to propane regulator that features a QCC1 connection with large hand nut that attaches to the propane tank. A high quality aftermarket part at a cost effective price.

Is your gas line cracked, split, or damaged? Is your regulator faulty and not supplying enough fuel to your burners? Replace your faulty regulator and hose with this quality aftermarket part. Check your gas line for cracks, rodent tooth marks and potential leaks around fittings. The diaphragm inside the regulator can become damaged or weakened. Over time, regulators experience wear from exposure to heat, weather, and general use. Order your replacement hose and regulator assembly from Grillparts.com today!

What’s Included:

• (1) 5/16in. x 24in. hose with attached regulator assembly with integrated QCC1 to-tank connection.
• Instruction sheet.
• Quality aftermarket part.

5/16in. ID propane/LP gas hose in 40 inch length with a brass 3/8in. female hex nut flare connector, assembled to propane regulator that features a QCC1 connection with large hand nut that attaches to the propane tank. A high quality substitute at a lower price point than Weber #99281.

Is your gas line cracked, split, or damaged? Is your regulator faulty and not supplying enough fuel to your burners? Replace and/or faulty regulator with this quality aftermarket part. Check your gas line for cracks, rodent tooth marks and potential leaks around fittings. The diaphragm inside the regulator can become damaged or weakened. Over time, regulators experience wear from exposure to heat, weather, and general use. Order your replacement hose and regulator assembly today!

What’s Included:

• (1) 5/16in. x 40in. hose with attached regulator assembly with integrated QCC1 to-tank connection.
• Instruction sheet.
• Quality aftermarket part.

10ft. length of 3/8in. ID flexible Stripwound gas hose and Quick Connect kit with 3/8in. fittings. Certified for natural gas or propane connection to existing fixed gas supply line. Please measure fitting size and assure prior to ordering.

Quick connect kits make it easy to connect and disconnect the grill from a fixed gas supply line quickly and without tools. This convenience is especially beneficial if you need to move the grill or store it away when not in use.

What’s Included:

• 10ft. of 3/8in. ID flexible Stripwound gas hose with 3/8in. fittings.
• Quick Connect Fittings: Includes a 3/8in. Quick Connect fitting (that screws onto a 3/8in. NPT male pipe thread) and a 3/8in. SAE female hex nut (that connects to the BBQ grill manifold), and a compression fitting for fast release.

12ft. length of 3/8in. ID flexible Stripwound gas hose and Quick Connect kit with 3/8in. fittings. Certified for natural gas or propane connection to existing fixed gas supply line. Please measure fitting size and assure prior to ordering.

Quick connect kits make it easy to connect and disconnect the grill from a fixed gas supply line quickly and without tools. This convenience is especially beneficial if you need to move the grill or store it away when not in use.

What’s Included:

• 12ft. of 3/8in. ID flexible Stripwound gas hose with 3/8in. fittings.
• Quick Connect Fittings: Includes a 3/8in. Quick Connect fitting (that screws onto a 3/8in. NPT male pipe thread) and a 3/8in. SAE female hex nut (that connects to the BBQ grill manifold), and a compression fitting for fast release.

14ft. length of 3/8in. ID flexible Stripwound gas hose and Quick Connect kit with 3/8in. fittings. Certified for natural gas or propane connection to existing fixed gas supply line. Please measure fitting size and assure prior to ordering.

Quick connect kits make it easy to connect and disconnect the grill from a fixed gas supply line quickly and without tools. This convenience is especially beneficial if you need to move the grill or store it away when not in use.

What’s Included:

• 14ft. of 3/8in. ID flexible Stripwound gas hose with 3/8in. fittings.
• Quick Connect Fittings: Includes a 3/8in. Quick Connect fitting (that screws onto a 3/8in. NPT male pipe thread) and a 3/8in. SAE female hex nut (that connects to the BBQ grill manifold), and a compression fitting for fast release.

Need to swap between a Natural Gas and Propane (or vice-versa) Gas Regulation? This Convertible gas regulator is for use with natural gas (NG) or propane (LP) fuel, and comes preset for natural gas regulation (4in. water column) and can be quickly and easily converted to propane (10in. water column) regulation. This versatility allows users to easily switch between different gas sources without needing to replace the regulator.

How easy is it to convert the regulator?
Simply remove the seal cap and invert/reverse the plunger (the plunger is threaded at each end, simply unscrew to remove, flip and screwed-in to install) then replace the seal cap.

Dimensions: Overall length measures 3in., square diaphragm casing measures 2-3/8in x 2-3/8in.

Features:

• Convertable to/from Natural Gas to/from Propane Gas Regulator
• 1/2in. NPT inlet and outlet openings and a fuel flow directional arrow.
• Rated 1/2 PSIG.  

23in. length, Stainless Steel Hose Protector/rodent guard with spring coil construction. Fits over 3/8in. and 5/16in.  propane gas hose.

Easy install — simply slide the guard over the propane hose at the fitting end. Protects the hose from kinking, touching hot surfaces on the inside of your BBQ grill, and helps to prevent rodents from chewing on your propane gas hose. Made in USA.

Propane hose/regulator assembly "not included", and is shown for display purposes only.

Weber Two Output Electronic Ignition Module With Screw-On Push Button Battery Cap for Weber® Spirit 200, Spirit 300 Series Models 2012 and Older with Electronic Ignition. Utilizes one AAA Battery (not included). Features an attached metal heat shield, module mounting jam nut/lock ring, 2 male flat spade color-coded output terminals and a gray screw-on style push button/battery cap with lightning bolt symbol. 

Why a new electronic ignition module for your Weber? You go to fire up the grill and all you get is silence. No spark, no flame, just disappointment. Why do these ignition modules decide to throw in the towel? Environmental factors – moisture, heat, and grease can all take their toll on delicate electronic components, causing them to malfunction. Insufficient voltage or fluctuations in electrical current can lead to failure. Like all electronic components, ignition modules have a finite lifespan. Replace your Weber 2 Output Port Electronic Ignition Module and light your way to a better grilling experience!

Fits Weber® Spirit 200 and Weber® Spirit 300 Series Models with Electronic Ignition manufactured in 2012 and prior years.

What’s Included:

• (1) Weber Push Button Start Electronic Ignition Module with 2 Outputs for 2012 and Older Spirit 200 and Spirit 300 models.
• Attached metal heat shield
• Module mounting jam nut/lock ring
• 2 male flat spade color-coded output terminals
• Push button/battery cap with lightning bolt icon 

Weber Grills threaded screw-on gray rubber push button/battery cap for Electronic Ignition Modules that utilize a "AAA" battery. Gray rubber push button features printed lightning bolt icon.

This Weber Push Button Battery Cap has threads that screws onto the module. For the "Twist and Lock" type mounting version, see part# 81316.

What’s Included:

• (1) Weber Push Button Battery Cap - Screw-on Type - for Weber Electronic Ignition Modules

Looking for a Push Button Battery Cap with Twist and Lock? See part# 81316.

Genuine Weber® Push Button Ignitor Kit: Push Button (with lock-nut mounting), Wiring, Electrode and Collector Box Assembly for Weber Spirit (pre-2002), Weber Platinum I and II, Weber Genesis 1000 to 5500, Weber Genesis Silver and Gold (pre-2002).

Main burner Weber® Push Button Ignitor Kit contains a lock-nut style mount push button with double pole (2 wire connection terminals). Includes the gas collector box with electrode, and 14-1/2in. wiring. 

Push Button Ignitor Kit fits most the following Pre-2002 Weber Models:
Fits Weber Spirit (pre-2002), Weber Platinum I and II, Weber Genesis 1000 to 5500, Weber Genesis Silver and Weber Gold (pre-2002).

(NOTE: Push button has different appearance because of the newer lock-nut mounting vs. snap-in, and is now black in color).

• (1) Genuine Weber Push Button Ignitor Kit with Button Assy, Wiring, Electrode and Gas Collector Box 
• Instructions Included
• Replacement push button igniter kit for Weber gas grills main burners on older grills
• Genuine Weber OEM replacement part

Weber Grills Twist and Lock mounting gray rubber push button/battery cap for Weber Electronic Ignition Modules that utilize a "AAA" battery. Gray rubber push button features printed lightning bolt icon.

This Weber Push Button Battery Cap has Twist and Lock for fixing the cap to the Ignition Module. For the Screw-On type mounting version, see part# 30158201.

What’s Included:

• (1) Weber Push Button Battery Cap - Twist and Lock - for Weber Electronic Ignition Modules

Looking for a Push Button Battery Cap that has Screw On mounting? See part# 30158201.

Genuine Weber® Push Button Ignitor Kit: Push Button (with snap-in mounting tabs), Wiring, Electrode and Collector Box Assembly for most Weber Grills manufactured after 2001.

Main burner Weber® Push Button Ignitor Kit contains a snap-in style mount push button with double pole (2 wire connection terminals). Includes the gas collector box with electrode, and 14-1/2in. wiring. 

Compatibility:

• Push Button Ignitor Kit fits most Weber Grills manufactured after 2001 with “Stopwatch Engineered“ Quick Assembly.

DOES NOT work with:

• Weber Summit Models
• Weber Genesis Silver C or Genesis Gold C model grills that utilize a single igniter that lights the main grill as well as the side burner.

What’s Included:

• (1) Genuine Weber Snap-in Push Button Ignitor Kit with Button Assy, Wiring, Electrode and Gas Collector Box 
• Instructions Included
• Replacement push button igniter kit for Weber gas grills main burners on a variety of grills
• Genuine Weber replacement part, replaces Weber Part 7510 and 307510

Complete Electronic Ignitor Kit for Weber® Spirit 200, Spirit 300 Series Models 2012 and Older. Includes a Genuine Weber Two Output Electronic Ignition Module With Screw-On Push Button Battery Cap paired with gas Collector Box, Electrode and 18in. Wiring Assembly. Utilizes one AAA Battery (not included). Features an attached metal heat shield, module mounting jam nut/lock ring, and a gray screw-on style push button/battery cap with lightning bolt graphic. 

Why a new electronic ignition kit for your Weber Spirit 200/300? You go to fire up the grill and all you get is silence. No spark, no flame, just disappointment. Why do these ignition modules decide to throw in the towel? Environmental factors – moisture, heat, and grease can all take their toll on delicate electronic components, causing them to malfunction. Insufficient voltage or fluctuations in electrical current can lead to failure. Like all electronic components, ignition modules have a finite lifespan. Replace your Weber Electronic Ignition Module, Electrode, Collector box and wiring with this awesome kit and light your way to a better grilling experience!

Fits Weber® Spirit 200 and Weber® Spirit 300 Series Models with Electronic Ignition manufactured in 2012 and prior years.

What’s Included:

• (1) Weber Push Button Start Electronic Ignition Module with 2 Outputs for 2012 and Older Spirit 200 and Spirit 300 models.
• Attached metal heat shield
• Module mounting jam nut/lock ring
• Push button/battery cap with lightning bolt icon
• (1) Weber Collector Box, Electrode and 18in. Wiring assembly

Gas Collector Box, Electrode and Wiring Assembly for Weber Spirit 200 and 300 Series grills (2012 and Older) and Weber Genesis 300 Series model year 2007.

Electrode with with 19-1/2in. wires that terminate with flat female spade fittings, preassembled into the Gas Collector Box for Weber Grills with Electronic Ignition System. High quality after market part.

Fits the following Weber® Gas grills:

• Weber Spirit 200 Series-manufactured in 2012 and prior years
• Weber Spirit 300 Series-manufactured in 2012 and prior years
• Weber Genesis 300 Series-manufactured in 2007

What’s Included:

• (1) Gas Collector Box, Electrode & Wiring Assy. for Weber Spirit 200/300 (2012 and older) and Genesis 300 (2007) Model Electronic Ignitions

Gas Collector Box, Electrode and Wiring Assembly for Weber grill that utilize a manual Push-Button Piezo Style Spark Generator.

Electrode with with 19-1/2in. wires. The black molded in wire from the electrode has a round connector end and the white wire terminates with two flat female spade connector ends.  Preassembled into the Gas Collector Box for Weber Grills with Manual "Push-Button" Piezo Spark Generators. High quality after market part.

What’s Included:
(1) Gas Collector Box, Electrode & Wiring Assy. for Weber Piezo style plunger-push-button spark generators.
(See part# UP7B for replacement Spark Generator)
 

20in. Red Igniter Wire with one insulated female Spade terminal on one end, to one insulated female Round terminal on opposite end.

What’s Included:

• (1) 20in. Igniter Wire for Weber Grills and Other Brands that require flat female spade to round female terminal connection points.

Piezo Ignition Push Button Spark Ignitor with Palnut (lock nut) threaded mounting. Universal part that fits an unbelievable assortment of gas grill brands and outdoor appliances. Plunger push button with double pole: flat side connector and round bottom connector.

What’s Included:
(1) Piezo Ignition Plunger Push Button Ignitor Spark Generator and Palnut Lock Nut.

Genuine Weber gas grill lid temperature gauge, indicator-thermometer with a 1-13/16in. dial face; measures internal grill temperatures from 150°F to 600°F/50°C to 350°C degrees. Temperature probe diameter is 1/4in. extends 1-1/2in. into grill hood body. Includes mounting wing nut.

Weber Temperature Gauge fits many Weber gas and charcoal grill models, including:

• Weber Spirit 2013 and 2014
• Weber Q
• Weber Genesis
• Weber Charcoal Kettles
• Replaces Weber Part # 7581, 60392 and 91384

Measurements:

• Diameter of thermometer dial face: 1-13/16in.
• Probe Length: 1-1/2in.

What’s Included:

• (1) Genuine Weber gas grill temperature gauge/indicator/thermometer (1-13/16in. dial face)
• (1) Mounting wing nut.
• Genuine Weber Part.
• Does not include decorative bezel.

Genuine Weber® Grills easy to clean, disposable aluminum foil disposable grease drip pan liners. Perfect-fit 8-1/2in. x 6in. Liners, 10 per package.

A simple disposable drip pan liner will save you from greasy maintenance. Line the drip tray of your grill and make the disposal of grease easy and clean!

Fitment:

• Compatible with Weber Q, Pulse, Lumin, Weber Traveler, Spirit, Spirit II, 2022 Genesis 300/400, Genesis II 200/300, Genesis.

What’s Included:

• (10) Weber Aluminum Foil Grease Tray Liners (8-1/2in. x 6in.)

Genuine Weber Rotisserie Motor for Weber Gas Grills with a rotisserie including Weber Summit series rotisseries. Rotisserie motor is 120V, and spins at 2.5-3.0 RPM, and has a 20lb. load weight limit.

Genuine Weber Replacement Rotisserie Motor for Weber Gas Grills features a black plastic casing with a stainless steel backing plate, a weather resistant On/Off switch, 34in. long cord/plug and installation instructions.

Looking for a Complete Rotisserie Kit for your grill? Try our Universal Grill Deluxe Electric Rotisserie Kit 

What’s Included:

• (1) Genuine Weber Replacement Rotisserie Motor for Weber Gas Grills:
• 120V electric motor, 2.5-3.0 RPM, 20lb weight limit
• Black plastic casing with a stainless steel backing plate
• Weather resistant On/Off switch
• 34in. cord with plug
• Installation instructions.
• Genuine Weber Part.

Does Not Fit: 

• Does not fit/replace Weber Charcoal Kettle rotisseries.
• Does not replace Ducane grill brand rotisserie motors.
   

Genuine Weber Premium Custom Fit Grill Cover for Weber Spirit Model gas grills. Features a waterproof, fade resistant polyester material that breathes for better moisture control and has fastening straps to secure the cover to the grill so you won’t find it in your neighbors yard. Dimensions are 51in. across wide, 27in. from front to back, and 42in. tall.

A Weber Premium Custom Fit Grill Cover is like the superhero cape for your BBQ, enhancing its looks when not in action; and it's not just about keeping sun, rain, snow, and debris funking up the grills looks; it's about protecting your investment. Protect your vulnerable grill from weather damage, and keep critters like squirrels and birds from turning your grill into their personal playground with a grill cover from grillparts.com.

Fits the following Weber grills:

• Spirit II 300 Series (2018 and Newer)
• Spirit 300 Series (2017 and older)
• Spirit 200 Series (2012 and Older). 

What’s Included:

• (1) Weber Premium Custom Fit Grill Cover for Weber Spirit Model gas grills.
• Genuine Weber Part.

Genuine Weber replacement gas grill Aluminum Catch Pan and Catch Pan Steel Holding Bracket that fits most Weber gas grills manufactured prior to 2008.

If your greasy, messy catch pan and mounting holder has seen better days, swapping it out for a new genuine Weber Aluminum Catch Pan along with the Weber Catch Pan Steel Holding Bracket can get your grill back on track and prevent a serious mess below your grilled masterpieces. Keep your grill in top-notch shape with this genuine replacement part from Grillparts.com.

Measures: 9in. x 7-1/4in. x 3in., and fits the following Weber Models:

• Weber Spirit prior to 2008 (does not fit side-mount or front-mount control panel models manufactured after 2008)
• Weber Genesis 1000-5500
• Weber Genesis Silver/Gold/Platinum (except Gold/Platinum 6 burner models)
• Weber Platinum I/Platinum II
• Weber Summit

What’s Included:

• (1) Weber Grease Catch Pan 
• (1) Weber Grease Catch Pan Mounting Holding Bracket
• Genuine Weber Part

Don’t forget replacement Disposable Foil Catch Pan Liners part# 6415. 

Set of two 9-1/8in. Aluminum Weber Catch Pan Tray Support Rails with mounting screws for Weber Spirit E-210 Model Years 2007-2008. Replacement Catch Pan Rails have an updated design, and are attached to your grill by screwing one screw into the center of the rail. The two positioning tabs on the rails are to be inserted into the old screw holes.

Weber Grease Catch Pan Tray Support Rails Fit the following Weber Gas Grill Models:

• Weber Spirit E-210 Model Years 2007-2008.
• Please measure your parts before ordering.

What's Included:

• (2) 9-1/8in. Aluminum Weber Catch Pan Tray Support Rails 
• (2) Mounting Screws
• Genuine Weber Part.

Genuine Weber Aluminum Grease Catch Pan and One Single Disposable Foil Liner. Fits most Weber Genesis, Genesis II (2016+), Spirit, Summit Silver/Gold/Platinum and Summit 400/600 (prior to 2000) gas grills.

IMPORTANT: Please verify Catch Pan dimensions:
Pan measures 8-5/8in. x 6-1/8in. wide (width measurement includes the folded side rail extension).

Fits the following Weber Gas Grills:

• Weber Genesis
• Genesis II (2016+)
• Spirit
• Summit Silver/Gold/Platinum
• Summit 400/600 (prior to 2000) 

What's Included:

• (1) Weber Grills Aluminum Grease Catch Pan With Foil Liner, 8-5/8in. x 6-1/8in.
• (1) Disposable Foil Liner
• Foil liners available in a pack of 10, Part# 6415.
• Genuine Weber Part
• Please verify dimensions

Set of two 9-1/8in. Aluminum Weber Catch Pan Tray Support Rails for Weber Genesis Silver A model years 2000-2006, and Spirit 500 model years 1992-1999. Two included mounting screws per rail (four screws total).

Important Note: These replacement Catch Pan Rails will ONLY fit older models that used the rails with 2 holes. They will not fit the newer models; where the production cook boxes have 3 mounting holes.

Weber Grease Catch Pan Tray Support Rails Fit the following Weber Gas Grill Models:

• Weber Genesis Silver A model years 2000-2006
• Spirit 500 model years 1992-1999.

What's Included:

• (2) 9-1/8in. Aluminum Weber Catch Pan Tray Support Rails 
• (4) Mounting Screws
• Genuine Weber Part.

Genuine Weber replacement ambient heat temperature thermometer for Weber Spirit, Genesis, Platinum Series II, Master Touch, and Performer grills.

May also be used as a stand alone, portable thermometer to check internal meat temperature.

Fits the following Weber grills:

• Weber Platinum II
• Weber Genesis Silver
• Weber Genesis Gold B/C
• Weber Genesis 1000-5500 Series
• Spirit E/S-310
• Spirit 300 Series with side-mounted controls
• Weber Master Touch Kettle
• Weber Performer Kettle

What's Included:

• (1) Weber grill hood Temperature Gauge, Analog Gas Grill Thermometer - (140-550°F/60-288°C)
• 5-1/2in. length probe through-mounts on the grill body.
• Probe Diameter: 1/8in.
• Gauge Face Diameter: 1-3/4in.

Genuine Weber Porcelain Enameled Steel slide-out bottom tray catch pan with centered drain for Weber Genesis Silver A, Spirit 500 and Spirit 200 Series models. 16-13/16in. x 9-3/8in. x 3-1/4in. bottom grease catch tray is made of durable black porcelain enameled steel making cleanup easier, and features a centered drain hole opening that supports the grease catch pan and bracket, (sold separately-see part 7515).

Fits the following Weber Models:

• Weber Genesis Silver A
• Weber Spirit 500 Series
• Weber Spirit 200 Series
• Measure before ordering.
• Replaces Weber Part# 85897. Genuine Weber Part.

What’s Included:

• (1) Weber Grill Grease Catch Tray with Centered Drain:
• Black porcelain enameled for easy clean up and durability.
• 16-13/16in. x 9-3/8in. x 3-1/4in.
• Please measure the existing tray to ensure this is the correct part. Parts can look nearly identical but only fit specific Weber grills.
• Refer to your grill’s assembly guide for installation
• Genuine Weber Part.

High quality aluminum slide-out bottom tray catch pan with centered drain for Weber Genesis Silver A, Spirit 500 and Spirit 200 Series models. 16-13/16in. x 9-3/8in. x 3-1/4in. bottom grease catch tray is made of aluminum for rust-free durability, and features a centered drain hole opening that supports the grease catch pan and bracket, (sold separately-see part 7515).

Fits the following Weber Models:

• Weber Genesis Silver A
• Weber Spirit 500 Series
• Weber Spirit 200 Series
• Measure before ordering.
• Replaces Weber Part# 85897.

What’s Included:

• (1) Aluminum Grease Catch Tray with Centered Drain for Weber Grills:
• Crafted in durable Aluminum.
• 16-13/16in. x 9-3/8in. x 3-1/4in.
• Please measure the existing tray to ensure this is the correct part. Parts can look nearly identical but only fit specific Weber grills.
• Refer to your grill’s assembly guide for installation

Centered hole supports the grease catch pan and bracket, sold separately-see part# 7515)